How to Make a Headband, Version 4: Headband with Ties

Headband with Ties - 1
Headband with Ties - 2

Silk headband measuring 2" (51 mm) wide by 17" (43 cm) long with 13" (33 cm) long ties. The headband is connected at the back with covered elastic measuring 0.5" (13 mm) wide by 4" (10 cm) long.

Materials

  • Woven fabric, like lightweight cotton or silk
  • 0.5" (13 mm) wide elastic–you’ll need a length of about 4.5" (11 cm), but you can wait to cut it until the fitting stage
  • Safety pin or loop turner

Instructions

Measuring and Cutting

  • Main Piece (including ties): Cut 1 rectangle from your fabric as shown in Diagram 1. The 44" (112 cm) length creates ties about 13" (33 cm) long; adjust the length if you want longer or shorter ties. The width range of 3.5" (89 mm) to 8.5" (22 cm) results in finished headband widths ranging from 1.5" (38 mm) to 4" (10 cm), respectively. To determine the exact fabric width to cut, multiply your desired finished headband width by two and add 0.5" (13 mm).
  • Connector Piece: Cut 1 rectangle from your fabric as shown in Diagram 1.
  • Note: Any grainline orientation should be fine, but laying the long sides of the rectangles crosswise (i.e., perpendicular to the selvage) will use the least fabric yardage.

    Diagram 1

    Diagram 1

Sewing

  1. Fold the short sides of the main piece in half with right sides together and, using a 0.25" (6 mm) seam allowance, sew the long raw edges together to create a tube, as shown in Diagram 2. Repeat with the connector piece.
  2. Diagram 2

    Diagram 2
  3. Turn the main piece right side out and press so that the seam is positioned at center back (CB). Repeat with the connector piece. (Use a safety pin or loop turner to turn the pieces right side out if needed.)
  4. Insert the elastic inside the connector piece using a safety pin or loop turner.
  5. Sew the elastic and connector piece together at one end with a 0.25" (6 mm) seam allowance, as shown in Diagram 3. (On the other end, just leave the end of the elastic sticking out for now; you can pin the end of the connector piece to the elastic to keep it in place if needed).
  6. Diagram 3

    Diagram 3
  7. Fold the main piece in half lengthwise and mark it with chalk or a fabric marker 8.5" (22 cm) away from the fold in both directions, as shown in Diagram 4.
  8. Diagram 4

    Diagram 4
  9. If your headband is wider than 1.5" (38 mm), pleat the main piece at each mark to make it about 1.5" (38 mm) wide, as shown in Diagram 5. Pin or baste stitch the pleats to secure them.
  10. Diagram 5

    Diagram 5
  11. Lay the connector piece down on top of the main piece, both with CB seams facing up. Align the stitchline at the end of the connector piece (Step 4) with one of the marks on the main piece, as shown in Diagram 6. At the mark, fold the sides of the main piece over the connector piece (the folded sides will overlap a little), and sew all layers together.
  12. Diagram 6

    Diagram 6
  13. Test the fit by trying on the headband while stretching the free end of the elastic to the other mark on the main piece. Cut elastic to desired length, including an extra 0.25" (6 mm) for a seam allowance.
  14. Repeat Step 4 with the other ends of the elastic and connector piece.
  15. Repeat Step 7 with the other ends of the connector piece and main piece, making sure the headband is not twisted.
  16. Remove the basting stitches made in Step 6, if any.
  17. (Optional) Cut the ends of the ties at an angle as shown in Diagram 7.
  18. Diagram 7

    Diagram 7
  19. Tuck the ends of the ties 0.25" (6 mm) to the inside and edgestitch the openings closed.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>